Latest News
Plastic egg trays can warp during washing when excessive heat, prolonged exposure, uneven spray pressure, or improper loading places stress on the material. For operators, even a slight change in shape can make trays difficult to stack, separate, or feed into handling equipment. Understanding how an Egg tray washer affects different tray materials is the first step toward preventing deformation without compromising cleaning.
Warping is rarely caused by one setting alone. A tray that tolerates a short hot wash may deform when it pauses under the spray, enters a heated drying section, or supports the weight of other trays while still warm. The useful question is not just “How hot is the washer?” but “What happens to the tray throughout the entire cycle?”
Plastic becomes softer as its temperature rises. If a tray is heated beyond the limits appropriate for its material and design, its ribs, corners, or flat surfaces can bend under their own weight or under mechanical pressure. Once cooled, the tray may retain that distorted shape.
Different trays can behave differently even when they look alike. Resin type, additives, wall thickness, previous use, and manufacturing quality all affect heat resistance. A temperature that works for one supplier’s tray is not automatically safe for another’s.
Check the tray manufacturer’s washing and drying guidance before changing the program. If the tray material or temperature limit is unknown, ask the supplier rather than relying on a generic setting for “plastic.” Also verify the actual temperature at relevant stages with a suitable, calibrated instrument: a tank display may not represent the temperature at the spray outlet or inside a drying section.
Do not solve a warping problem by simply turning down the wash temperature without review. The revised cycle must still meet the site’s cleaning and sanitation requirements. Consult the person responsible for food safety when adjusting a validated process.
Finding the point at which deformation appears can save a great deal of trial and error. Inspect representative trays at safe access points, following the machine’s operating and lockout procedures. Look before washing, after washing and rinsing where accessible, and after drying and cooling. Never reach into a running machine or open a guarded section unless the equipment is stopped and made safe.
Mark a small set of trays from the same batch and follow them through the process. Comparing them with unwashed trays from that batch makes it easier to distinguish a machine-related issue from variation already present in the stock.
A tray does not experience heat only at the moment it enters the washer. It may be exposed during pre-washing, main washing, rinsing, and drying. A slow conveyor or an unscheduled stop can extend that exposure substantially.
Pay particular attention to trays left inside a hot zone during breaks, jams, or downstream stoppages. A setting that is acceptable during continuous operation may become troublesome when the conveyor stops. Follow the equipment manufacturer’s instructions for clearing or managing trays during interruptions; do not bypass guards or reach into heated sections.
If a change in conveyor speed is being considered, assess both sides of the decision. Faster travel may reduce heat exposure, but it can also reduce cleaning contact time. Confirm that the adjusted cycle still removes the relevant soils and meets the facility’s hygiene procedure.
Spray pressure is valuable for removing stubborn contamination, but more pressure is not always better. A strong or uneven jet can push against a thin tray, particularly when heat has made the plastic more flexible. Bent nozzles, partial blockages, or incorrect nozzle orientation can concentrate the force on one area.
Inspect the spray system according to the maintenance schedule. Clean blocked nozzles, check their alignment, and use the pressure range recommended for the washer and the trays. Reducing pressure alone may leave egg residue behind, so any adjustment should be checked against actual cleaning results.
Loading deserves the same attention. Trays that overlap, ride at an angle, catch on guides, or enter the machine with insufficient support can be forced out of shape. Operators should use the intended orientation and spacing, keep guides correctly adjusted, and avoid feeding damaged trays that may snag. If the washer handles several tray sizes, check that the conveyor and restraints are suitable for the particular size in use.
A tray may leave the dryer looking acceptable but bend under a stack if it has not cooled sufficiently. Allow trays to cool on a clean, suitable support before stacking or applying pressure, in line with the site’s hygiene and handling procedures. Avoid placing hot trays on an uneven surface or leaning them against a wall, where their own weight can encourage bending.
Rapid or uneven cooling can also contribute to dimensional changes in some plastic products. If distortion appears during cooling, review the cooling method with the tray supplier and equipment provider rather than assuming that the coldest possible rinse is the best solution.
Where trays remain dirty after a gentler cycle, investigate the soil and loading pattern before restoring aggressive settings. Dried-on egg residue may require an approved pre-soak or a different cleaning sequence. Use only cleaning chemicals compatible with the tray material and follow the chemical supplier’s instructions: chemical incompatibility or incorrect concentration can contribute to plastic deterioration over time.
Seek technical support if deformation persists across controlled tests, appears only with a particular tray design, or coincides with unusual conveyor movement or temperature readings. Provide tray dimensions and material details, photos of the distortion, operating settings, and the stage at which the change first appears. This information helps the supplier assess whether the issue calls for a process adjustment, replacement parts, or a different support arrangement.
Zhucheng Maikang Mechanical and Electrical Technology Co., Ltd. supplies washing equipment for trays and other reusable containers and can discuss configurations for different handling needs. Its broader food-processing range also includes the Fruit & Vegetable Pulping Machine, used for pulping and separating residue in products such as fruit purée and sauces.
A reliable washing routine protects both hygiene and the trays themselves. By tracing where deformation begins, checking actual exposure, and making controlled adjustments, operators can address the cause instead of repeatedly replacing trays that come out misshapen.